bel power solutions 152 north 3rd street, suite 805 san jose, ca 95112 usa ? 201 5 bel power solutions, inc. north america +1 - 866.513.2839 asia - pacific +86.755.29885888 europe, middle east +353 61 225 977 tech.support@psbel.com d - 2000 - st02 _ 001 ? output power 2000 w ? single - phase 230 vac input ? p ower factor > 0.99 ? t otal h armonic d istortion < 5% ? main output: +40 v to +50 v (+20 v to +50 v by remote control) ? auxiliary output: +12 v / 500 ma ? current and voltage m onitor ing ? remote enable the bpeu series of ac/dc converters is available with multiple outputs and output power from 1300 w up to 3000 w. all models incorporate active power factor correction (pfc). other standard features include current and voltage monitoring, overvoltage, overtemperature as well as short circuit protection. these power supplies were designed to power radio - frequency power amplifier (rfpa) applications in th e broadcasting industry.
BPEU2000 ? 201 5 bel power solutions, inc. 866.513.2839 tech.support@psbel.com d - 2000 - st02 _ 001 parameter description / condition voltage 184 C 264 vac single - phase frequency 4763 hz efficiency > 90% @ full - load @ 230 vac inrush c urrent 30 apk @ 230 vac power factor 0,99 @ full - load @ 230 vac thd 5% @ pout 1 kw output voltage setting by trim (vdc) voltage setting by ext. 0 5vdc (vdc) inom (a) imax (a) tolerance % ripple % power (w) v1 +40 to +50 * +20 to +50 ** 40 45 < 2 2 2000 v2 12 n/a 0. 5 1 5 < 5 6 * v1 adjustable manually by multi - turns trimmer set on board (see page 2 "+48 vadj") ** see "voltage output adjustement procedure" section at page 2 parameter description / condition over - load v1: constant current limiting (see curve) short - circuit v1: hiccup mode (with auto recovery) over - voltage v1: set point = 56v 5%, not automatic return to operation over - t emperature: automatic return to operation with hysteresis general: ac side thermal fuses (t) parameter description / condition output v1 current monitor im l inear analogic signal 100 mv 1a (internal impedance 3 k ? ) output v1 voltage monitor vm l inear analogic signal 1 / 10 vout (internal impedance 2 k ? ) high temperature alarm ota open - collector, max. sink 4 ma; alarm = low (on = 70c; reset = 60c tolerance 5%) over temperature alarm otp open - collector, max. sink 4 ma; alarm = low (on = 80c; reset = 70c tolerance 5%) under voltage input alarm pwr fail o pen - collector, max. sink 4 ma; alarm = low (set point vin < 180 v ac ) output v1 remote enable c onnected to com = power - on, not connected = power - off (minimum current sink 5 ma) parameter description / condition operating temperature: - 10 to +50c @ full - load (forced air - cooling , see thermal protection ) storage temperature: - 20 to +85c
BPEU2000 ? 201 5 bel power solutions, inc. 866.513.2839 tech.support@psbel.com d - 2000 - st02 _ 001 parameter description / condition safety: en60950 - 1:2006+a11:2009 / en60065:2002+a1:2006 emc: en61000 - 6 - 4:2007 harmonics c urrent: en61000 - 3 - 2 (class a) ce mark parameter description / condition input 3 pole screw type terminal block 24 a , 2. 5 mm 2 output v1 2 pole screw type terminal block 57 a , 16 mm 2 signals / controls / output v2 male flat type connector 10 pole dil figure 1 - connections voltage output adjustment procedure v1 set the jumper on pin 1 - 2 to adjust vout by on board trimmer "+48 vadj" set the jumper on pin 2 - 3 to reduce linearly v out set by trimmer by a 0 - 5 vdc external signal: 0 vdc output v1 = voltage set by trimmer "+48 vadj" 5 vdc output v1 = voltage set by trimmer "+48 vadj" - 20 vdc
BPEU2000 ? 201 5 bel power solutions, inc. 866.513.2839 tech.support@psbel.com d - 2000 - st02 _ 001 parameter description / condition material case: aluzinc 10/10 mm cover: aluzinc 10/10 mm fixing n 4 hole ? 5 mm (see dimensions ) dimensions (w x h x d) 128 x 72 x 350 mm notes: tolerances 0. 5 mm max figure 2 - mechanical drawing figure 3 C cooling method
BPEU2000 ? 201 5 bel power solutions, inc. 866.513.2839 tech.support@psbel.com d - 2000 - st02 _ 001 figure 4 C output characteristics figure 5 C voltage output adjustments figure 6 C efficiency figure 7 C power factor figure 8 C conducted noise nuclear and medical applications - products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. specifi cations are subject to change without notice. 0 10 20 30 40 50 5 4 3 2 1 0 vprog. vout trimmer setting 10 15 20 25 30 35 40 45 50 0 10 15 20 25 30 35 40 45 50 5 vout iout 66 68 70 72 74 76 78 80 82 84 86 88 90 92 2100 1800 1500 900 300 0 600 1200 % pout , 9 0 , 0 92 94 0 , , 96 0 0 , 98 1 0 300 600 900 1200 1500 1800 2100 p.f. pout
|
